Link Aggregation

Link Aggregation Introduction

Link aggregation aggregates multiple physical Ethernet ports into one logical link, also called an aggregation group. It allows you to increase bandwidth by distributing traffic across the member ports in the aggregation group. In addition, it provides reliable connectivity because these member ports can dynamically back up each other.

Network Diagram

Figure 1-1 Network diagram for link aggregation configuration

Networking and Configuration Requirements

Switch A aggregates ports GigabitEthernet 1/0/1 through GigabitEthernet 1/0/3 to form one link connected to Switch B and performs load sharing among these ports.

Configuration Example
1)        Manual aggregation mode:
#
link-aggregation group 1 mode manual
#
interface GigabitEthernet1/0/1
port link-aggregation group 1
#
interface GigabitEthernet1/0/2
port link-aggregation group 1
#
interface GigabitEthernet1/0/3
port link-aggregation group 1
#
2)        Static LACP aggregation mode:
#
link-aggregation group 1 mode static
interface GigabitEthernet1/0/1
port link-aggregation group 1
#
interface GigabitEthernet1/0/2
port link-aggregation group 1
#
interface GigabitEthernet1/0/3
port link-aggregation group 1
#
Link aggregation support of release 6300 of the 7500 series Ethernet switches differs slightly. The aggregation group configuration procedure is as follows:
l              Static aggregation mode
#
interface Bridge-Aggregation1
#
interface GigabitEthernet1/0/1
port link-aggregation group 1
#
interface GigabitEthernet1/0/2
port link-aggregation group 1
#
interface GigabitEthernet1/0/3
port link-aggregation group 1
#
l              Dynamic aggregation mode
#
interface Bridge-Aggregation1
link-aggregation mode dynamic
#
interface GigabitEthernet1/0/1
port link-aggregation group 1
#
interface GigabitEthernet1/0/2
port link-aggregation group 1
#
interface GigabitEthernet1/0/3
port link-aggregation group 1
#
Configuration Guidelines
l          Compatibility problems may occur when devices are connected to one another through static aggregation in different software, since the implementation approach of static aggregation varies with software. You can use the display version command to view the software version information.
l          An RRPP-configured port, a static MAC address or blackhole MAC address-configured port, a voice VLAN-enabled port, and an 802.1x-enabled port cannot be added to an aggregation group.

Comments

INSTALL CISCO VPN CLIENT ON WINDOWS 10 (32 & 64 BIT). FIX REASON 442

This article shows how correctly install Cisco VPN Client (32 & 64 bit) on Windows 10 (32 & 64 bit) using simple steps, overcome the ‘ This app can’t run on this PC ’ installation error , plus fix the Reason 442: Failed to enable Virtual Adapter error message . The article applies to New Windows 10 installations or Upgrades from earlier Windows versions and all versions before or after Windows 10 build 1511 . To simplify the article, we’ve broken it into the following two sections: How to Install Cisco VPN client on Windows 10 (clean installation or upgrade from previous Windows), including Windows 10 build prior or after build 1511 . How to Fix Reason 442: Failed to enable Virtual Adapter on Windows 10 Figure 1. The Cisco VPN Client Reason 442: Failed to enable Virtual Adapter error on Windows 10 HOW TO INSTALL CISCO VPN CLIENT ON WINDOWS 10 (NEW INSTALLATIONS OR O/S UPGRADES) The instructions below are for new or clean Windows 10 inst...

Linux File and Directory Permissions

file & directory protection is a essential of any OS and Linux OS is no exception for it! These authorizations allow you to choose exactly who can access your files & directory, providing an overall improved system security. There was one of the major flaws in the older Windows operating-system where, by standard, all users can see each other people's information (Windows 95, 98, Me). For overcoming it, editions of the Windows based computer system such as NT, 2000, XP and 2003 lot more security features added. They fully support file & directory permissions, just as Linux system has since the beginning. Together, we'll now assess a directory listing from our Lab Linux system hosting server, to help us understand the information provided. a simple 'ls' command will give you the file and directory listing within a given directory, including the option '-l' will display number of new areas that we are going to discuss here:

How to create a Hirens Boot CD 15.2 USB Disk

Hiren’s BootCD (HBCD) is a bootable CD that contains a set of tools that can help users to fix their computer if their system fails to boot. More specifically, HBCD contains hardware diagnostic programs, partition tools, data recovery utilities, antivirus tools and many other tools to fix your computer problems. I write this article because I use Hiren’s BootCD frequently to troubleshoot computer problems, specially when a computer doesn’t boot anymore due to a virus attack or due to a corrupted file system. In this article you will find instructions on how to put Hiren’s BootCD on a USB flash drive (stick) in order to troubleshoot computer problems in the future.

Networking Tips Tricks

Search This Blog