Skip to main content

Novell Netware Remote Printer Configuration Guide

Remote printers are a method of allowing a printer, attached to a workstation, to be available for use by all members of the network. This is useful if the server is far from the machine where people will be working.

First you must establish a single print queue for each printer. This will be done through the PCONSOLE program. Simply select the Print Queue menu and then press INSERT and type the name of a queue. Repeat this procedure for each queue.

You must next create a single print server for each 256 printers you wish to host. To do this move to the final choice on the main menu of PCONSOLE, and select the Print Server menu. Press INSERT and enter the name of the new print server.

There is only one thing to configure for each print queue. After the print server is created enter the print queue list and select the first queue. Then select the option for "Print Server's Serviced" and press INSERT to present a list of servers. Select the appropriate server. Repeat for each queue.

In the Print Server menu you must configure the printers. To do this you must enter the printer configuration menu. You must name each printer, starting at printer 0, and select its location. All printers labeled REMOTE are not on the server, but are located on a workstation. The printers labeled LPT or SERIAL are on the server. When you select a remote port, it must correspond to the port that the printer is connected to on the remote computer. Repeat this for each printer.

Once this is completed, enter the printer service menu and select the queue each printer will service. By assigning a single queue to each printer, you control where the output of the jobs, since capture directs by queue, not printer name.

The final step is enabling the print server, by typing LOAD PSERVER at the console. Then to enable a remote printer simply run the RPRINTER command on each workstation that you wish to have a remote printer attached to. Once you run RPRINTER on the station, it will remain loaded until you disable it, or reboot the machine.

Note: THIS DOCUMENT ASSUMES FAMILIARITY WITH PCONSOLE!!

Comments

Popular posts from this blog

INSTALL CISCO VPN CLIENT ON WINDOWS 10 (32 & 64 BIT). FIX REASON 442

This article shows how correctly install Cisco VPN Client (32 & 64 bit) on Windows 10 (32 & 64 bit) using simple steps, overcome the ‘ This app can’t run on this PC ’ installation error , plus fix the Reason 442: Failed to enable Virtual Adapter error message . The article applies to New Windows 10 installations or Upgrades from earlier Windows versions and all versions before or after Windows 10 build 1511 .  To simplify the article, we’ve broken it into the following two sections: How to Install Cisco VPN client on Windows 10 (clean installation or upgrade from previous Windows), including Windows 10 build prior or after build 1511 . How to Fix Reason 442: Failed to enable Virtual Adapter on Windows 10 Figure 1. The Cisco VPN Client Reason 442: Failed to enable Virtual Adapter error on Windows 10 HOW TO INSTALL CISCO VPN CLIENT ON WINDOWS 10 (NEW INSTALLATIONS OR O/S UPGRADES) The instructions below are for new or clean Windows 10 inst...

How to Disable SSL for Webmin

Webmin is a Web application that enables administrators to manage Linux servers. Webmin runs on a Web server at port 10000. Miniserv is the name of the Web server application that handles the Webmin Web application. By default, Miniserv uses SSL. However, you can disable SSL for Webmin Miniserv by editing the configuration file for the Web application. With SSL disabled, you can access the Webmin application over a standard HTTP connection. Step 1 Open a terminal window on the Linux server. You can also SSH into the server if you do not have physical access to the machine. Step 2 Type the following command at the command prompt and press the “Enter” key: nano /etc/webmin/miniserv.conf This command opens the Miniserv configuration file in the Nano text editor.

Error 651: How to Fix it in Windows 7/8

If you are a windows user then it is possible that you have Face Error 651 Anytime. There are many windows user who get affected by this error code 651 while working online. If you are one of those windows user, then keep reading this article and carefully read out the following Detailed solutions which I have gathered after researching various websites, articles, forums etc. When using Windows 7 built-in PPPoE wizard with a modem working in bridge mode, it fails and error code 651 appears. The similar problem happens on Windows Vista or previous versions as well. For example, Error code 678 on Windows XP is equivalent to error code 651 on Windows 7. Error code 651 usually occurs when user tries to connect it’s broadband in windows 7 operating system. It shows a message that Your modem (or other connecting devices) has reported an error and Usually the message will be “Connection failed with error 651” .Fix Error 651 In such cases user tries to resta...