Skip to main content

Device Link Detection Protocol (DLDP)


DLDP Introduction

Sometimes, unidirectional links may appear in networks. On a unidirectional link, one end can receive packets from the other end but the other end cannot. Unidirectional links result in problems such as loops in an STP-enabled network.
As for fiber links, two kinds of unidirectional links exist. One occurs when fibers are cross-connected, as shown in Figure 1-2. The other occurs when one end of a fiber is not connected or one fiber of a fiber pair gets disconnected, as illustrated by the hollow arrows in Figure 1-2.
Figure 1-1 Unidirectional fiber link: cross-connected fiber

Figure 1-2 Unidirectional fiber link: fiber not connected or disconnected

Device Link Detection Protocol (DLDP) can detect the link status of a fiber cable or twisted pair. On detecting a unidirectional link, DLDP can shut down the related port automatically or prompt users to take measures as configured to avoid network problems.

Configuring DLDP

Network Diagram


Networking and Configuration Requirements

l          Device A and Device B are connected through two fiber pairs, in which two fibers are cross-connected, as shown in Figure 1-3.

Configuration Example

l          Device A
#
 dldp enable
 dldp interval 6
 dldp work-mode enhance
 dldp delaydown-timer 2
#
interface GigabitEthernet1/0/50
 dldp enable
#
interface GigabitEthernet1/0/51
 dldp enable
l          Device B

Configuration Guidelines

1)        DLDP can detect unidirectional links only after all links are connected. Therefore, before enabling DLDP, make sure that optical fibers or copper twisted pairs are connected.
2)        DLDP takes effect only when it is enabled both globally and on a port.
3)        Set the interval for sending Advertisement packets to a value not longer than one-third of the STP convergence time. If the interval is too long, STP loops may occur before unidirectional links are torn down, and it takes a long time for the device to detect unidirectional links, thus causing more traffic forwarding errors; if the interval is too short, unnecessary Advertisement packets can be generated to consume bandwidth. Therefore, you are recommended to use the default value.
4)        To enable DLDP to operate properly, make sure the DLDP authentication modes and the passwords of the two sides of a link are the same.
5)        Destination MAC addresses of DLDP packets fall into two types: class A and class B, which is dependent on the software versions running on the device. To ensure that DLDP operates properly, interconnected devices must use destination MAC addresses of the same class. 

Comments

Popular posts from this blog

INSTALL CISCO VPN CLIENT ON WINDOWS 10 (32 & 64 BIT). FIX REASON 442

This article shows how correctly install Cisco VPN Client (32 & 64 bit) on Windows 10 (32 & 64 bit) using simple steps, overcome the ‘ This app can’t run on this PC ’ installation error , plus fix the Reason 442: Failed to enable Virtual Adapter error message . The article applies to New Windows 10 installations or Upgrades from earlier Windows versions and all versions before or after Windows 10 build 1511 .  To simplify the article, we’ve broken it into the following two sections: How to Install Cisco VPN client on Windows 10 (clean installation or upgrade from previous Windows), including Windows 10 build prior or after build 1511 . How to Fix Reason 442: Failed to enable Virtual Adapter on Windows 10 Figure 1. The Cisco VPN Client Reason 442: Failed to enable Virtual Adapter error on Windows 10 HOW TO INSTALL CISCO VPN CLIENT ON WINDOWS 10 (NEW INSTALLATIONS OR O/S UPGRADES) The instructions below are for new or clean Windows 10 inst...

How to Disable SSL for Webmin

Webmin is a Web application that enables administrators to manage Linux servers. Webmin runs on a Web server at port 10000. Miniserv is the name of the Web server application that handles the Webmin Web application. By default, Miniserv uses SSL. However, you can disable SSL for Webmin Miniserv by editing the configuration file for the Web application. With SSL disabled, you can access the Webmin application over a standard HTTP connection. Step 1 Open a terminal window on the Linux server. You can also SSH into the server if you do not have physical access to the machine. Step 2 Type the following command at the command prompt and press the “Enter” key: nano /etc/webmin/miniserv.conf This command opens the Miniserv configuration file in the Nano text editor.

Error 651: How to Fix it in Windows 7/8

If you are a windows user then it is possible that you have Face Error 651 Anytime. There are many windows user who get affected by this error code 651 while working online. If you are one of those windows user, then keep reading this article and carefully read out the following Detailed solutions which I have gathered after researching various websites, articles, forums etc. When using Windows 7 built-in PPPoE wizard with a modem working in bridge mode, it fails and error code 651 appears. The similar problem happens on Windows Vista or previous versions as well. For example, Error code 678 on Windows XP is equivalent to error code 651 on Windows 7. Error code 651 usually occurs when user tries to connect it’s broadband in windows 7 operating system. It shows a message that Your modem (or other connecting devices) has reported an error and Usually the message will be “Connection failed with error 651” .Fix Error 651 In such cases user tries to resta...